Manuál Florabest IAN 270730 Motorová pila

Manuál

14

GB

Before you start up the electric chainsaw,

mount the sword, mount the chain, adjust

the chain, ll up with chain oil and check

the automatic lubrication and chain brake

function.

Mount the saw bar

F

1. Lay the saw on a at surface.

2. Turn the fastening bolt (14) anti-

clockwise and loose the chain

adjustment ring (

A

13) to remove

the sprocket chain wheel cover-

ing (15).

3. To t the new bar, place the bar

(4) onto the bar bolt (22) with

the tensioning plate pointing out-

wards (24).

Mount the saw chain

G

1. Spread the chain (5) out into a

loop with the cutting edges run-

ning clockwise .

2. Relax the tensioning screw (24)

against the clockwise

direction.

3. Slide the saw chain (5) into the

bar guide groove. To mount the

guide bar (4), raise it to an angle

of approx. 45 degrees. This will

make it easier to replace the saw

chain (5) onto the sprocket (25).

It is normal that the saw chain (5)

is slack. Sagging in the chain is

normal.

4. Pre-tighten the chain (5) by turn-

ing the tensioning plate (24)

clockwise.

5. Position the sprocket chain wheel

covering (15). First place the tab

(26) on the cover into the corre-

sponding notch on the plate (15).

Only lightly tighten the fastening

bolt (14), as you will still have to

tension the saw.

Note that the saw can re-oil.

Please note that the saw re-oils after use

and oil may leak out if it is stored on its

side or on the head. This is a normal

process due to the necessary ventilation

opening on the upper edge of the tank and

does not constitute a reason for complaint.

As each saw is checked during production

and tested with oil, a small residue may

be in the tank despite draining, which may

slightly dirty the housing with oil in transit.

Please clean the housing with a cloth.

Prior to changing the chain, the nut of the

guide rail must be cleaned of dirt because

dirt deposits available can cause the chain

to break out of the rail. The deposits can

also absorb the chain oil. So the conse-

quence would be that the chain oil would

not or only a small part of it would reach

the underside of the rail and the lubrication

would be reduced.

Tensioning the saw chain

Regularly tightening the saw chain pro-

vides safety for the user and reduces and/

or prevents wear and chain damages.

Before the start of work and in approx. 10

minute intervals, we recommend the user to

examine the chain tension and correct it, if

necessary.

The chain warms up when working with

the saw and thus expands slightly. These

“expansions” can be expected especially

from newer chains.

IB-270730-FKS_2200_E3-CB4-03112015-rev03-ts.indb 14 05.11.15 16:08

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Florabest IAN 270730 Motorová pila papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Florabest. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Florabest IAN 270730 Motorová pila v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Florabest Motorové pily
Další manuály Motorové pily

Často kladené otázky o Florabest IAN 270730 Motorová pila

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Florabest IAN 291822 Motorová pila

Manuál

Florabest IAN 292285 Motorová pila

Manuál

Florabest FAHE 18 B2 Motorová pila

Manuál

Florabest FBKS 52 A1 Motorová pila

Manuál

Florabest IAN 68655 Motorová pila

Manuál

Florabest IAN 64606 Motorová pila

Manuál

Florabest IAN 56393 Motorová pila

Manuál

Florabest IAN 285178 Motorová pila

Související kategorie