Manuál Hikoki CJ 18DSL Vykružovačka

Manuál

7

English

○ When the pilot lamp fl ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about 3

seconds to confi rm that the battery being charged with

charger is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery

is reinserted within 3 seconds, the battery may not be

properly charged.

○ Check the voltage of the in-car power source when

the pilot lamp fl ickers in green (every 0.2 seconds)

continuously. (UC18YML2)

If the voltage is 12V or lower, it indicates that the car

battery has weakened and cannot be charged.

○ If the pilot lamp does not blink in red (every second) even

though the charger cord or cigarette lighter connecting

plug is connected to the power, it indicates that the

protection circuit of the charger may be activated.

Remove the cord or plug from the power and then

connect it again after 30 seconds or so. If this does

not cause the pilot lamp to blink in red (every second),

please take the charger to the HiKOKI Authorized

Service Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 1

181

Charging 2

181

Changing blades 3

181

Switch operation 4

181

Remaining battery indicator 5

181

Adjusting the orbital operation 6

181

Splinter guard 7

182

Mounting and dismounting the chip

cover

8

182

Housing the hexagonal bar wrench

9

182

Mounting the guide (sold separately)

and rectilinear cutting

10

182

Mounting the guide (sold separately)

and cutting a circle or a circular arc

11

182

Cutting metallic materials 12

182

Angular cutting 13

183

Pocket cutting 14

183

Concerning cutting of stainless steel

plates

15

183

Connecting with cleaner 16

183

Sub base 17

183

Selecting accessories ―

184

SELECTION OF BLADES

To ensure maximum operating effi ciency and results, it is

very important to select the appropriate blade best suited to

the type and thickness of the material to be cut. The blade

number is engraved in the vicinity of the mounting portion

of each blade. Select appropriate blades by referring to

Table 3.

MAINTENANCE AND INSPECTION

CAUTION

Pull out battery before doing any inspection or

maintenance.

1. Inspecting the blade

Continued use of a dull or damaged blade will result in

reduced cutting effi ciency and may cause overloading of

the motor. Replace the blade with a new one as soon as

excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signifi cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signifi cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to fi ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modifi ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI power tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the power tool, undismantled, with the GUARANTEE

CERTIFICATE

found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

0000Book̲CJ18DSL.indb70000Book̲CJ18DSL.indb7 2019/07/2518:54:372019/07/2518:54:37

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Hikoki CJ 18DSL Vykružovačka papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Hikoki. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Hikoki CJ 18DSL Vykružovačka v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Hikoki Vykružovačky
Další manuály Vykružovačky

Často kladené otázky o Hikoki CJ 18DSL Vykružovačka

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Hikoki CJ 36DB Vykružovačka

Manuál

Hikoki CJ 110MV Vykružovačka

Manuál

Hikoki CJ 65V3 Vykružovačka

Manuál

Hikoki CJ 18DA Vykružovačka

Manuál

Nupower NPE55 Vykružovačka

Manuál

Parkside IAN 306438 Vykružovačka

Manuál

Parkside IAN 275382 Vykružovačka

Manuál

Parkside IAN 338176 Vykružovačka

Související kategorie