Manuál EGO ST1500E-F Strunová sekačka

Manuál

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1500E-F

11

EN

NOTICE: The trimmer head is parallel to the ground at

a proper cutting distance without the operator bending

over (Fig. P).

For safe and better operation, put on the shoulder strap

across the shoulder as Fig. P. Adjust the shoulder strap in

a comfortable operating position. Hold the line trimmer

with both hands: One hand on the rear handle and the

other hand on the front-assist handle.

There are two ways to release the strap. Take it away

from your shoulder directly (Fig. Q) or press the hook of

the strap and take it apart from the tubing clip xed on

the shaft (Fig. R).

WARNING: The shoulder strap is also a quick

release mechanism in hazardous situation. When

an emergency occurs, take it off from your shoulder

immediately, no matter what way the strap is in.

STARTING/STOPPING THE LINE TRIMMER (Fig. S)

To Start

Press down the lock-off lever then depress the trigger.

Different pressure on the trigger results in variable rotat-

ing speed of the cutting line. More pressure, higher speed.

To Stop

Release the lock-off lever and the trigger.

NOTICE: The motor runs only when the lock-off lever and

trigger are both pressed.

WARNING: Always remove the battery pack from

the line trimmer during work breaks and after nishing

work.

USING THE LINE TRIMMER

WARNING: To avoid serious personal injury, wear

goggles or safety glasses at all times when operating

this unit. Wear a face mask or dust mask in dusty

locations.

Clear the area to be cut before each use. Remove all ob-

jects, such as rocks, broken glass, nails, wire, or line, that

can be thrown or become entangled in the cutting attach-

ment. Clear the area of children, bystanders, and pets.

At a minimum, keep all children, bystanders and pets at

least 15m away; there still may be risk to bystanders from

thrown objects. Bystanders should be encouraged to wear

eye protection. If you are approached, stop the motor and

cutting attachment immediately.

Before each use, check for damage/worn parts

Check the bump head, guard and front-assist handle

and replace the parts that are cracked, warped, bent, or

damaged in any away.

The line-cutting blade on the edge of the guard can dull

over time. It is recommended that you periodically sharp-

en it with a le or replace it with a new blade.

WARNING: Always wear gloves when mounting the

guard or servicing the blade. Take care of the blade on

the guard and protect your hand from cutting.

After each use, clean the trimmer.

CAUTION: Obstructions in the vents will prevent

the air from owing into the motor housing and result in

overheating or damaged of the motor.

◾ Use only mild soap and a damp cloth to clean the tool.

Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

◾ Keep air vents in the motor housing from debris at all

times.

WARNING: Never use water for cleaning your

trimmer. Avoid using solvents when cleaning plastic

parts. Most plastics are susceptible to damage from

various types of commercial solvents. Use clean cloths

to remove dirt, dust, oil, grease, etc.

ADJUSTING CUTTING LINE LENGTH

The trimmer head allows the operator to release more

cutting line without stopping the motor. As line becomes

frayed or worn, additional line can be released by lightly

tapping the spool retainer on the ground while operating

the trimmer (Fig. T).

NOTICE: Line release will become more difcult as the

cutting line becomes shorter.

WARNING: Do not remove or alter the line cutting

blade assembly. Excessive line length will cause the motor

to overheat and may result in serious personal injury.

LINE REPLACEMENT

NOTICE: Always use the recommended nylon cutting

line with a diameter that does not exceed 2.4 mm.

Using line other than that specied may cause the

line trimmer to overheat or become damaged.

WARNING: Never use metal-reinforced line,

wire, or rope, etc. These can break off and become

dangerous projectiles.

1. Remove the battery pack.

2. Remove the remaining cutting line, if necessary.

Simply pull it out by hand.

3. Rotate the spool retainer in the arrow direction,

as necessary, to align the LOAD line on the spool

retainer with the eyelets in the spool base (Fig. U).

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu EGO ST1500E-F Strunová sekačka papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat EGO. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému EGO ST1500E-F Strunová sekačka v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro EGO Strunové sekačky
Další manuály Strunové sekačky

Související produkty

Manuál

EGO ST1511E Strunová sekačka

Manuál

EGO ST1530E Strunová sekačka

Manuál

EGO ST1510E-T Strunová sekačka

Manuál

EGO ST1401E-ST Strunová sekačka

Manuál

EGO STX3800 Strunová sekačka

Manuál

EGO ST1300E-S Strunová sekačka

Manuál

EGO ST1610E-T Strunová sekačka

Manuál

EGO BC3800E Strunová sekačka

Související kategorie