Manuál EGO CS2000E Motorová pila

Manuál

56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E 9

EN

B-1 Lock Nuts D-2 Guide Bar Groove

B-2

Chain-tensioning

Bolt

E-1 Drive Sprocket

D-1 Chain Drive Links

NOTICE: When looping the saw chain onto the guide

bar, make sure that, after mounting the guide bar onto

the saw, match the cutter pattern and rotation direction

arrow on the housing. If they face in opposite directions,

reassemble the saw chain onto the guide bar with the

cutters facing the same direction (Fig. E2).

7. Replace the side cover onto the chain saw housing

and fully tighten the two lock nuts.

8. Rotate the chain by hand to check whether the chain

is properly assembled without binding. Otherwise,

reassemble the chain and bar.

NOTICE:

To extend the guide bar life, invert the bar

occasionally.

ADJUSTING THE CHAIN TENSION

◾ Stop the motor and remove the battery pack before

adjusting the chain tension. Turn the chain-tensioning

bolt clockwise or counterclockwise to adjust chain

tension (Fig. F) until the chain seats snugly against the

guide bar with the drive links in the guide bar groove.

◾ A cold chain is correctly tensioned when there is no

slack on the underside of the guide bar and the chain

is snug, but it can be turned by hand without binding.

The chain must be re-tensioned whenever the flats on

the drive links do not sit in the bar groove.

◾ During normal saw operation, the temperature the

chain will increase. The drive links of a correctly

tensioned warm chain will hang approximately 1.3 mm

out of the bar groove (Fig. G).

NOTICE: New chains tend to stretch; check chain tension

frequently and tension as required.

NOTICE: A chain tensioned while it is warm may be too

tight upon cooling. Check the cold tension before next use.

OPERATION

WARNING: Do not allow familiarity with this product

to make you careless. Remember that a careless fraction

of a second is sufficient to inflict serious injury.

WARNING: Do not use any attachments or

accessories not recommended by the manufacturer of

this product. The use of attachments or accessories not

recommended can result in serious personal injury.

WARNING: To prevent accidental starting that could

cause serious personal injury, always remove the battery

pack from the tool when assembling parts, making

adjustments, cleaning, or when not in use.

Before each use, inspect the entire product for damaged,

missing, or loose parts, such as screws, nuts, bolts, caps,

etc. Securely tighten all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced.

APPLICATION

You may use this product for basic felling, limbing, pruning,

and woodcutting of lumber and trees.

NOTICE: The machine is to be used only for its prescribed

purposes. Any other use is deemed to be a case of misuse.

FILLING BAR AND CHAIN LUBRICANT

WARNING: Do not smoke or bring any fire or flame

near the oil or the chain saw. Oil may spill and cause a

fire.

NOTICE: The chain saw is not filled with oil at the time of

purchase. It is essential to fill the tank with oil before use.

The chain is automatically lubricated with chain oil during

operation.

1. Position the chain saw on its side with the tank cap

facing upwards.

2. Clean the oil tank cap and the area around it to ensure

that no dirt falls into the oil tank.

3. Lift up the semicircular plate and rotate the oil tank

cap counterclockwise to remove it (Fig. H).

4. Carefully pour the bar and chain oil into the tank. Fill to

the bottom of the fill neck.

5. Wipe off any excessive oil and replace the cap.

NOTICE: Check the oil level frequently and fill when the oil

level falls below the minimum line. Never operate the chain

saw if the oil is not visible.

ATTACHING/DETACHING THE BATTERY PACK

Use only with EGO’s battery packs and chargers listed

in Fig. A2.

Fully charge before rst use.

To Attach

Align the battery ribs with the mounting slots and press the

battery pack down until you hear a “click” (Fig. I).

To Detach

Depress the battery-release button and pull the battery pack

out (Fig. J).

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu EGO CS2000E Motorová pila papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat EGO. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému EGO CS2000E Motorová pila v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro EGO Motorové pily
Další manuály Motorové pily

Často kladené otázky o EGO CS2000E Motorová pila

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

EGO CS1410E Motorová pila

Manuál

EGO CS1610E Motorová pila

Manuál

EGO CS1401E Motorová pila

Manuál

EGO CS2005E Motorová pila

Manuál

EGO CSX5000 Motorová pila

Manuál

EGO CS1600E Motorová pila

Manuál

EGO CS1614E Motorová pila

Manuál

EGO CSX3000 Motorová pila

Související kategorie