Manuál EGO CS2000E Motorová pila

Manuál

56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS2000E10

EN

STARTING/STOPPING THE CHAIN SAW

NOTICE: Before starting the chain saw, check for the oil

level, saw teeth sharpness and properly working kickback

brake paddle. Besides, balanced footing and proper distance

away from the ground are needed.

To Start (Fig. K)

1. Pull the chain-kickback brake paddle towards the front

handle to the operating position (Fig. K).

2. Firmly grasp the front handle with the left hand and the

rear handle with the right hand.

WARNING: To avoid injury, always use the chain saw

with the right hand grasping the gripping area of the rear

handle (Fig. L).

3. Press and hold the lock-off button with the thumb of

your right hand, then squeeze the trigger switch with

the fingers of your right hand to start the saw (Fig. L).

L-1 Gripping Area

4. Release the lock-off button and continue to squeeze

the trigger switch for continued operation.

5. The further the trigger switch is depressed, the greater

the chain speed. Adjust the speed to suit the task at

hand.

WARNING: Do not attempt to start the saw when the

saw chain is in a cut.

To Stop

1. Move the chain saw away from cutting area, and

then release the trigger switch to stop the chain saw.

2. Push the chain-kickback brake paddle forward to the

brake position to engage the chain brake (Fig. K).

WARNING: Always remove the battery pack from the

machine during work breaks and after finishing work.

CHANGING SPEED MODE (FIG. M)

This machine features three speed modes. Each speed mode

the limits the maximum speed of the chain saw. The speed

mode will change with every press of the chain speed button.

The speed bars on the LCD screen will display the active

speed mode: one bar for low speed, two bars for medium

speed, and three bars for high speed. The low speed mode

(ECO) provides better control of the machine and longer

operating time per charge.

M-1 Speed Bars M-5 Fuel-gauge Circle

M-2 Bluetooth Icon M-6

Headlight/

Bluetooth Button

M-3 Headlight Icon M-7

Chain Speed

Button

M-4 Brake Icon

NOTE: When using EGO battery pack rated 2.5Ah or less,

only the ECO mode is available. And use of EGO battery pack

rated less than 6.0Ah will not allow you to achieve high

speed. For best performance, we strongly recommend use of

EGO battery packs that are 6.0Ah (e.g., BA3360T) or more.

NOTE: The machine's speed memory function will

remember the last speed setting and activate it the next time

the machine is turned on.

NOTE: The LCD screen lights up when trigger switch is

pulled or when the speed button or headlight/Bluetooth

button is pressed. It will automatically turn off after

approximately 30 seconds of chain saw inactivity.

LED HEADLIGHT (Fig. N)

The LED headlight is located in the front of the chain saw

housing. The headlight provides illumination for increased

visibility and features 2 brightness levels.

To turn on the headlight, press the headlight/Bluetooth button

(Fig. M) one time. The headlight will turn on in low brightness

level and the low brightness headlight icon will appear on

the LCD screen. Press the headlight/Bluetooth button again

to switch to high brightness level and the high brightness

headlight icon will appear on the LCD screen.

To turn off the headlight, press the headlight/Bluetooth button

the third time and the headlight icon will disappear from the

LCD screen.

N-1

Low Brightness

Headlight Icon

N-3 LED Headlight

N-2

High Brightness

Headlight Icon

OMNI-DIRECTIONAL CHAIN BRAKE SYSTEM (Fig.

O1 and Fig. O2)

WARNING: The omni-directional chain brake system

is not intended to act as a substitute to the standard/

traditional chain brake. The user should never rely on this

feature during operation of the chain saw to protect against

kickback. Always follow safety instructions related to kickback

mitigation found in the warning section of this manual.

When the omni-directional chain brake system is activated

and stops the saw, the brake icon will be flashing on the LCD

screen (Fig. M). Release the trigger switch, remove the saw

chain and guide bar from the wood, then restart the chain

saw.

NOTE: The sensors will only detect sudden motion of the

saw in the plane of the guide bar (fig. O1). The sensors will

not detect any sudden motion of the saw sideways (fig. O2)

(i.e., perpendicular to the plane of the guide bar).

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu EGO CS2000E Motorová pila papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat EGO. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému EGO CS2000E Motorová pila v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro EGO Motorové pily
Další manuály Motorové pily

Často kladené otázky o EGO CS2000E Motorová pila

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

EGO CS1410E Motorová pila

Manuál

EGO CS1610E Motorová pila

Manuál

EGO CS1401E Motorová pila

Manuál

EGO CS2005E Motorová pila

Manuál

EGO CSX5000 Motorová pila

Manuál

EGO CS1600E Motorová pila

Manuál

EGO CS1614E Motorová pila

Manuál

EGO CSX3000 Motorová pila

Související kategorie