Manuál Brabantia BBEK1003 Konvice

Manuál

32

capabilities or lack of experience and Knowledge if they

have been given supervision or instruction concerning

use of the appliance in a safe way and understand

the hazards involved. Children shall not play with the

appliance.

6. Do not immerse the Digital Kettle in water or any other

liquid.

7. Always place the Digital Kettle on a stable, flat heat-

resistant surface. Also ensure that the surface can take

the weight of the unit during use.

8. The Digital Kettle is intended for DOMESTIC USE ONLY

and should not be used for commercial purposes.

The Digital Kettle should only be used for its intended

purpose.

9. Do not leave the unit unattended when in use.

10. Do not move or lift the Digital Kettle while it is operating

or while it is connected to the mains electrical supply.

11. The use of attachments, not specifically recommended

by the manufacturer, must not be used as they may

cause personal injury or damage to the appliance.

12. Before cleaning the Digital kettle, allow it to cool down

13. Make sure that the Digital Kettle is switched 'OFF' and

remove the plug from the mains electrical supply when

it is not in use, before it is cleaned and while it is being

repaired.

14. To unplug the appliance, grasp the plug firmly and

remove it from the mains electrical supply. DO NOT

PULL ON THE CORD.

15. Check the Digital Kettle's power cord carefully regularly

for damage. If the power cord is damaged in any way,

it must be replaced by the manufacturer or its service

agent or a similarly qualified person in order to avoid an

electrical hazard.

16. Do not overfill the kettle. If the kettle is overfilled, boiling

water will be ejected.

17. Do not allow the power cord to hang over sharp table

edges or come into contact with hot surfaces.

18. To prevent the risk of electrical shock, do not immerse

the power cord, plug, or any non-removable parts of

this Digital Kettle in water or any other liquid.

19. Never use the Digital Kettle if it is damaged in any way.

20. All repairs should be done by a qualified electrician.

Improper repairs may place the user atrisk.

21. When handing this product over to a third party, ensure

that this instruction manual is supplied with the appliance.

22. The Kettle must not be submerged in water as any

contact with the electrical parts will create the risk

of malfunction and electric shock. Do not use the

appliance with damp or wet hands.

This instruction manual is also available on our website

www.brabantia.com

BEFORE FIRST USE

NOTE:

• The Digital Kettle must only be used with the supplied power base.

• Remove all the packaging material.

• Place the power base on a dry level surface.

• It is recommended that the Digital Kettle be washed and rinsed thoroughly before first use.

USING THE DIGITAL KETTLE

1. Ensure that the Digital Kettle is unplugged.

2. Open the lid by pressing the automatic lid button

3. Never fill the Digital Kettle when it is on its base.

4. Do not use the Digital Kettle without water.

5. Fill the Digital Kettle with the desired amount of fresh water. You may fill the Digital Kettle

through the spout as this will ensure good maintenance of the filter.

6. Ensure that the water level is filled to at least the MIN water level and do not exceed the MAX

level.

7. When the Digital Kettle has been filled, place it firmly on its base.

8. Ensure that the lid is properly closed by pressing it down firmly so as to close properly.

9. Connect the mains plug to the mains electrical supply making sure that the voltage and

frequency is the same as detailed on the rating plate found on the base of the Digital Kettle.

10. All the pre-set buttons on the handle will illuminate momentarily to indicate that there is power.

11. To start the Digital Kettle, press the desired water temperature pre-set button once. The Digital

Kettle will 'beep' once and the selected temperature button will flash until the water has

reached the pre-set temperature at which point the Digital Kettle will 'beep' 3 times indicating

that the cycle is complete.

12. You may change your selection at any stage during a pre-set cycle by simply pressing

another pre-set button once. The digital Kettle will 'beep' once indicating that a new pre-set

temperature has been selected and the new pre-set button will start flashing.

13. Please note that the surface of the heating element will maintain residual heat after heating.

BOIL MODE (STARTING WITH COLD WATER)

Select and press the pre-set 100°C button once. The Digital Kettle will 'beep' once and the 100°C

button will flash. It will continue flashing until the water temperature reaches the pre-set temperature

of 100°C/boiling point.

1. When the water starts heating up, the water colour illumination will be green, indicating that

the water temperature is below 70°C and is heating up.

2. When the water temperature reaches 70°C, the 70°C button will illuminate and the water

colour illumination will become blue (70-79°C).

3. When the water temperature reaches 80°C, both the 70°C and 80°C buttons will illuminate

and the water colour illumination will become orange (80-94°C).

4. When the water temperature reaches 95°C, the 70°C; 80°C and 95°C buttons will illuminate

and the water colour illumination will become red (95-100°C).

5. At 100°C/boiling point the Digital Kettle will 'beep' 3 times indicating that the boiling cycle is

complete. The 70°C; 80°C and 95°C buttons will switch off and the 100°C button will stop

flashing and become a steady light for 2 minutes and then it will switch off.

6. The red water colour illumination will continue for 2 minutes and then it will switch off.

7. Should you wish to change your pre-set temperature selection at any time during the boiling

cycle, simply press the new pre-set temperature button once (e.g. 80°C button) and the Digital

Kettle will beep once, indicating that a new pre-set water temperature has been selected. The

80°C button will start flashing.

8. THE DIGITAL KETTLE WILL SWITCH OFF AUTOMATICALLY as soon as the water reaches boiling

point or any other selected pre-set temperature. The Digital Kettle will automatically switch off

and 'beep' 3 times. The selected pre-set button will stop flashing and become a steady light

for 2 minutes and the colour illumination will continue for 2 minutes after which both lights will

switch off.

9. To switch off the Digital Kettle manually, press the selected pre-set button once and the Digital

Kettle will 'beep' once. The selected pre-set button will switch off, the water colour illumination

will switch off and the Digital Kettle will switch off. This can be done at any point during the

'Heat Up' or 'Keep Warm' cycles.

KEEP WARM MODE

The Digital Kettle offers a unique KEEP WARM MODE that can be used before, during or on completion

of the pre-set cycle. When the water temperature reaches 70°C the KEEP WARM function will hold

the temperature constant for 30 minutes.

KEEP WARM MODE starting with hot water

Once the pre-set cycle is complete, you may activate the 'Keep Warm' function by pressing any of the

pre-set buttons for 3 seconds until the Digital Kettle 'beeps' twice. The selected pre-set temperature

button will flash until the water reaches the new pre-set temperature and then the Digital Kettle will

'beep' 3 times. The selected pre-set temperature button will become a steady light and the selected

temperature will be maintained in 'Keep Warm' mode tor 30minutes. After 30minutes, the selected

pre-set button and the water colour illumination will switch off and the Digital Kettle will switch off

automatically. If a different temperature is required, change the selection at any time by simply

pressing a different pre-set button for 3 seconds until the Digital Kettle 'beeps' twice and the new pre-

set button starts flashing.

KEEP WARM MODE starting with cold water

Press the pre-set button for 3 seconds until the Digital Kettle beeps twice. The selected pre-set

button will flash as the water goes through its temperature and water colour illumination cycles until it

reaches the pre-set temperature at which point the Digital Kettle will beep 3times. The selected pre-

set button will become a steady light; the water colour illumination will remain on and the selected

temperature will be maintained in 'Keep Warm' mode for 30minutes. After 30minutes, the selected

pre-set button and the water colour illumination will switch off and the Digital Kettle will switch off

automatically.

PRE-SET TEMPERATURE OPTIONS

this means lights on this means lights flash this means lights off

Starting the heating up process from cold water

Water Illumination Start from cold water

below 70

70-79

80-94

95 or above

boil

power off within 2 min

power off after 2 min

Keep warm mode - Starting from cold water

Water Illumination Keep warm - Start from cold water

below 70

70-79

80-94

95 or above

boil

keep warm for 30min

over 30 min

Keep warm mode - Starting from hot water

Water Illumination Keep warm - Start from hot water

above 95

95-81

80-71

keep warm for 30min

over 30 min

The Digital Kettle offers 3 pre-set temperature settings for optimal tea and coffee brewing: 80°C,

95°C and 100°C.

GREEN TEA/OTHER TEAS 80°C COFFEE/TEAS 95°C BOIL/BLACK TEAS 100°C

GREEN TEA 80°C TEAS 80°C COFFEE|TEAS 95°C BOIL/BLACK

TEAS100°C

CEYLON GREEN APPLE DECAFFEINATED

COFFEE

BAGGED TEA

DARJEELING GREEN BLACK CHERRY INSTANT COFFEE

GRANULES

CHAI

NEPAL GREEN TEA BLACKCURRANT PLUNGER COFFEE CHAMOMILE

COCONUT CEYLON CINNAMON

ELDERFLOWER CHINA ROSE HERBAL

GINGER CHINA YUNNAN LEMONGRASS

JASMINE DARJEELING PERPPERMINT

LEMON EARL GREY RED

LYCHEE ENGLISH BREAK-FAST ROOIBOS

MANGO INDIAN CHAI SPEARMINT

ORANGE PASSIONFRUIT WHOLE LEAF

PEACH VANILLA WULONG

STRAWBERRY VIENNESE BLEND

NOTE:

This table is a recommended guide only and may vary depending on personal preference, brand and

age of tea/coffee used. Experiment with your favourite tea/coffee and select a temperature setting

option to suit your personal taste.

DESCALING

Furring up is a common problem in hard water areas, and it is recommended that you descale the

Digital Kettle regularly.

1. To descale, fill the Digital Kettle with 1 L cold water and add approximately 75ml vinegar.

2. Boil the water and allow it to stand overnight.

3. Re-boil the water the next day.

4. Discard the re-boiled water and refill the Digital Kettle with fresh water.

5. Boil the fresh water. This boiled water must also be discarded.

NOTE: Normal commercial descalers for kettles may also be used. Follow the instructions carefully for

the given descaler.

CLEANING AND MAINTENANCE

6. Remove the mains plug from the mains electrical supply before cleaning.

7. Do not immerse the Digital Kettle in water or any other liquid.

8. Avoid the use of solvents, polish, abrasive or aerosol cleaners as they may damage the surface

of the Digital Kettle.

9. Clean the exterior by wiping with a slightly dampened soft cloth.

10. The inside of the Digital Kettle may be cleaned using a mild detergent. It must be thoroughly

rinsed before re-use.

11. The removable mesh filter prevents scale from falling into your cup when pouring. This

filter neither treats nor removes the hardness of the water. Never remove the filter when the

appliance is full of hot water.

12. It is important to clean the filter regularly.

13. Remove the filter and place it under a running tap whilst wet, then dry it and brush it gently

before re-inserting it into the spout.

14. NOTE: Make sure that the Digital Kettle is thoroughly dried before reconnecting it to the mains

electrical supply.

WARRANTY EXCLUSIONS

The warranty will not be valid if:

1. The product has not been installed, operated or maintained in accordance with the

manufacturer's operating instructions provided with the product

2. The product has been used for any purpose other than its intended function.

3. The damage or malfunction of the product is caused by any of the following:

• Incorrect voltage

• Accidents (including liquid or moisture damage)

• Misuse or abuse of the product

• Faulty or improper installation

• Mains supply problems, including power spikes or lightning damage

• Infestation by insects

• Tampering or modification of the product by persons other than authorised service personnel

• Exposure to abnormally corrosive materials

• Insertion of foreign objects into the unit

• Used with accessories not pre-approved by Brabantia

Please refer to and heed all warnings and precautions in the Instruction Manual.

Due to continuous product development specifications may be subject to change without prior

notification.

ENVIRONMENT FRIENDLY DISPOSAL

Correct Disposal of this product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection

systems) The European Directive 2012/19/UE on Waste Facilities Electrical and Electronic

(WEEE) This marking shown on the product or its literature, indicates that it should not be

disposed with other household wastes at the end of its working life.

To prevent possible harm to the environment or human health from uncontrolled waste

disposal, please separate this from other types of wastes and recycle it responsibly to

promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product or their

local authority office, for details of where and how they can take this item for environmentally

safe recycling.

Non-contractual photo

Conscious of the quality of its products, the manufacturer reserves the right to make changes without

prior notice

NL

BELANGRIJKE VEILIGHEIDSMAATREGELEN

1. Lees de volgende veiligheidsmaatregelen grondig door

voordat u de digitale waterkoker inschakelt.

2. Bewaar deze handleiding op een veilige plek voor

toekomstige referentie. Bewaar ook de verkoopbon en

indien mogelijk, de doos met binnenverpakking.

3. Als u onderstaande instructies niet opvolgt, kan

dit leiden tot elektrische schokken, vuur of ernstig

persoonlijk letsel.

4. Voordat u de digitale waterkoker op de

stroomvoorziening aansluit, controleert u of de spanning

en de stroomvoorziening overeenkomen met de

specificaties weergegeven op het typeplaatje van het

apparaat.

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Brabantia BBEK1003 Konvice papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Brabantia. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Brabantia BBEK1003 Konvice v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Brabantia Konvice
Další manuály Konvice

Často kladené otázky o Brabantia BBEK1003 Konvice

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Brabantia BBEK1003MB Konvice

Manuál

Brabantia BBEK1001 Konvice

Manuál

Cecotec Thermosense 420 Vintage Light Green Konvice

Manuál

SilverCrest IAN 406536 Konvice

Manuál

Kampa Cascade Konvice

Manuál

Sencor SWK 7701GG Konvice

Manuál

Bosch TWK1M123 Konvice

Manuál

Kernau KSK 175 Konvice

Související kategorie