Manuál Vango Ravello 600 Stan

Manuál

TENT PITCHING INSTRUCTIONS – RAVELLO (UK)

Flysheet First Pitching:

 Open out flysheet and position in required direction

 Peg out the four main corners of the tent using the pegs supplied

 Locate inflation points on each beam

 Remove the valve cap (figure 1)

 Insert the correct pump adaptor, which will lock onto the valve (figure 2 & 3)

 There is no need to turn the white valve button as the adaptor will move this to the correct position

 Inflate all tubes to 7psi. The tubes MUST be guided into an arch as they are inflated.

 Final tube pressure MUST NOT exceed 8psi

 DO NOT OVER-INFLATE THE BEAMS

 Start with the centre tube and guide the beam into an upright position while it is inflating

 Inflate the other beams.

 A small amount of air may leak from the valve when it is being inflated but this is normal

 Remove the pump adaptor as soon as the beam is at the correct psi

 Replace the valve cap to create an air tight seal (figure 5 & 6)

 Ensure the tent is in a straight line

 The groundsheet should be flat and wrinkle free

 Peg out the remaining poles and pegging points using pin pegs at the base of poles

 Peg out ALL guy lines using pin-pegs ensuring that guy line fabric attachment points are evenly tensioned.

 Reposition and adjust tensioning where necessary

 Insert the shorter porch pole into front pole sleeve over doorway

 Push porch pole into an arch from opposite side and locate pole end onto pin system

CORRECT PUMP SET-UP:

 Pump Body > Pressure Valve > Pressure Gauge > Hose

 (Ensure the valve/gauge/hose are connected to the inflation port of the pump)

Inner Attachment:

 Open out inner tent inside flysheet and position doorways to correspond with the living area

 Starting from the rear corners of the tent, attach the elasticated hooks on the groundsheet to corresponding rings on the flysheet

 Suspend the inner by attaching toggles of inner tent through rings on inside of flysheet

 Do the rear first and work forward

Tension Band System:

 Remove Tension Band System from pockets and attach into the corresponding clips at the apex of the pole

 Adjust the straps until they are taut

 DO NOT OVERTENSION. Excess tension will alter the shape of the tent

TO DEFLATE AIRBEAM/ AIRAWAY/ AIRAWNING:

 To deflate the AirBeam (remove the cap (figure 7)) press & turn (figure 8) the button from CLOSED to OPEN

In the unlikely event of a puncture:

 Deflate the air beam. Unzip the internal flysheet sleeve which contains the affected beam.

 Remove the tube and its protective outer.

 The zips for the protective outer are cable tied together to prevent accidental access. Cut the cable tie and open the zip.

 DO NOT open these zips when the tube inflated.

 Remove the clear rubberised tube from the protective sleeve taking care when removing the valve from the sleeve.

 Partially inflate the tube and pass through a bucket or basin of water, looking for air bubbles. This will indicate location of puncture

 Use the repair patch provided and cover hole, using instructions on patch. Re-insert tube into protective outer, closing zip from both ends, so that zip pullers are in the flysheet sleeve

(this might be easier with the tube partially inflated)

AIRBEAM INFLATION:

AIRBEAM DEFLATION:

Aufbauanleitung - Ravello (DE)

Mit Außenzeltaufbau zuerst

 Außenzelt auslegen und korrekt ausrichten.

 Befestigen Sie die 4 Hauptecken des Zelts mit Hilfe der mitgelieferten Heringe

 Lokalisieren Inflation Punkte auf jeder Strahl

 Entfernen Sie die Ventilkappe

 Legen Sie die richtige Pumpenadapter , die auf das Ventil sperren wird

 Es besteht keine Notwendigkeit , um die weiße Ventilknopf drehen, da der Adapter wird diese in die richtige Position bewegen

 Pumpen Sie alle Schläuche auf 3psi auf. Die Schläuche MÜSSEN beim Aufpumpen in einen Bogen geformt werden.

 Der Schlauchdruck DARF letztendlich 4psi nicht überschreiten.

 TRÄGER NICHT ZU STARK AUFPUMPEN.

Figure 1

Remove

locking cap

Figure 3

Lock locking pump

connector

Figure 4

Inflate with

AirBeam pump

Figure 5

Insert locking

cap

Figure 6

Lock locking cap

Figure 8

Push button to deflate &

twist to open position

Figure 7

Unlock

locking cap

Figure 2

Insert locking pump

connector

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Vango Ravello 600 Stan papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Vango. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Vango Ravello 600 Stan v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Vango Stany
Další manuály Stany

Často kladené otázky o Vango Ravello 600 Stan

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Vango Vesta Air 850XL Stan

Manuál

Vango Utopia II Air TC 500 Stan

Manuál

Vango Avington Flow Air 500 Stan

Manuál

Vango F10 Krypton UL 2 Stan

Manuál

Vango Xenon UL 2 Plus Stan

Manuál

Vango Alderley Air 650XL Stan

Manuál

Vango Ventanas II Air TC 650XL Stan

Manuál

Vango Orava II 650XL Stan

Související kategorie