Manuál Tryton TDW1050 Vrtací kladivo

Manuál

5

operation; use protective gloves when changing the drill bit).

- Throwing back machined object or its fragment.

- Bending/breaking the drill.

The set includes:

ź drill - 1 piece

ź Auxiliary handle - 1 piece

ź Depth stop - 1 piece

ź Chuck key - 1 piece

ź User's manual - 1 piece

ź Warranty card - 1 piece

operators from exposure to vibrations, such as maintenance of the

electric tool and work tools, assurance of proper hand temperature, or

determination of the sequence of work operations.

n

,B,C

The vibration level value given refers to basic application of the tool. If the

tool is used for other applications or with other tools, or if it is not

maintained properly, the vibration level may differ from the values

given. The above-mentioned causes may lead to higher exposure to

vibrations during the whole work time.

One must implement additional safety measures to protect the

BEFORE YOU START:

Impact

1. Make sure that power supply parameters meet the requirements

provided on the drill nameplate.

2. Make sure the drill switch is in off position and switch lock (4) is

released. Do not put the device aside when the lock is on. To release

the lock press the switch (6) again.

3. The auxiliary handle (8) can be installed by inserting the handle

clamping ring onto the chuck and locking it by tightening the handle.

n Device components (see Fig. A ):

The depth stop (9) can be installed by inserting it into the hole of the

The numbering of device components refers to graphics presented on page

auxiliary handle and tightening the auxiliary handle to lock it.

2 of the user's manual:

1. Drilling chuck with a toothed ring

4. When using an extension cord make sure its parameters and cable

cross-section meet the drill power requirements. Extension cords

2. Operation mode switch drill / impact drill

should be as short as possible. When in use extension cords must be

3. Rotation direction switch

fully uncoiled.

4. Switch lock

5. Rotational speed control

OPERATION:

6. Switch

n Selecting a drill bit

7. Main handle

When drilling in concrete, bricks, stone masonry bits must be used. When

8. Auxiliary handle

drilling holes in metal, plastics, wood (hole diameters up to 6mm) use

9. Depth stop

metal bits.

10. Key for the drilling chuck with a toothed ring

When drilling holes with a diameter exceeding 6 mm in wood, use wood

drill bits.

SPECIFICATIONS:

n Fixing a drill bit

Insert a drill bit into the loosened chuck (1) and fix it by tightening jaws

by turning the outer ring clockwise with the key (10) inserted one by

another into 3 holes provided in the chuck body (see Fig.: B).

n Setting the drilling depth

The depth stop (9) can be used to set drilling depth.

Extend the drill stop to set the distance between depth stop tip and drill

bit tip that equals to the drilling depth required.

n Selecting an operation mode

źDrilling and tightening/undoing screws:

Set the operation mode switch (2) to position «drill» marked with

symbol - .

ź Impact drilling:

Set the operation mode switch (2) to position «impact drill» marked with

symbol - .

NOTE: Never change the operation mode when the drill chuck (1) rotates.

n Changing the rotation direction

Move the rotation direction lever (3) to a selected position until you feel

resistance. Symbols on the housing near the switch: R - clockwise

rotation, L- counterclockwise rotation.

NOTE: Never change the rotation direction when the drill chuck (1) rotates.

n Turning on/off

To turn the power tool on press its switch (6) button and keep it pressed.

To lock the switch in on position press the lock (4).

To turn the power tool off just release the switch (6) button or, when it is

locked with switch lock (4), press it for a moment and then release it.

Frequency

50 Hz

Power consumption

No load speed

Voltage

220-230 V

13 mm

Drill chuck (keyed)

Maximum hole diameter

steel

concrete

wood

- 10 mm

- 13 mm

- 25 mm

Sound pressure level (LpA)

Sound power level (LwA)

Vibration level according to valid standard EN 60745-2-1:2010

No impact drilling

main handle a

hD

(metal),

Impact drilling (concrete) a

hID

2

tolerance of measurements K=1,5 m/s

92,3 dB(A)

103,3 dB(A)

2

14,953 m/s

2

3,914 m/s

Equipment Class

Ingress protection

Weight (with no accessories)

3,0 kg

IP20

II

MODEL

TDW1050

0-2800 rpm

1050 W

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Tryton TDW1050 Vrtací kladivo papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Tryton. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Tryton TDW1050 Vrtací kladivo v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Tryton Vrtací kladiva
Další manuály Vrtací kladiva

Často kladené otázky o Tryton TDW1050 Vrtací kladivo

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Tryton TDW1200 K Vrtací kladivo

Manuál

Tryton TDW550 Vrtací kladivo

Manuál

Tryton TDW1050K Vrtací kladivo

Manuál

Tryton TDW1200 Vrtací kladivo

Manuál

Tryton TDW710 Vrtací kladivo

Manuál

Tryton TDW850K Vrtací kladivo

Manuál

Sharks SH 1050 Vrtací kladivo

Manuál

Metabo SB 660 Vrtací kladivo

Související kategorie