Manuál Skil 1215 AA Pásová bruska

Manuál

6

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• SKIL can assure awless functioning of the tool only

when original accessories are used

• This tool should not be used by people under the age of

16 years

• The noise level when working can exceed 85 dB(A); wear

ear protection

• Hold power tool by insulated gripping surfaces,

because the belt may contact its own cord (cutting a

“live” wire may make exposed metal parts of the power

tool “live” and could give the operator an electric shock)

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• This tool is not suitable for wet sanding

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• When sanding metal, sparks are generated; do not use

dustbag/dustbox/vacuum cleaner and keep other

persons and combustible material from work area

• Do not touch the running sanding belt

• Do not continue to use worn, torn or heavily clogged

sanding belts

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Alwaysdisconnectplugfrompowersourcebefore

making any adjustment or changing any accessory

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/o switch

- switch on/o the tool by pulling/releasing trigger A 2

! before the sanding surface reaches the

workpiece, you should switch on the tool

! before switching off the tool, you should lift it

from the workpiece

• Switch locking for continuous use

- pull trigger A 2

- press knob B 2 with your thumb

- release the trigger

- unlock the switch by pulling again trigger A 2 and

then releasing it

• Quick-changing of sanding belts (CLIC system) 4

! disconnect the plug

- lift lever C

- remove sanding belt

- insert new belt with arrows printed at inner side of belt

pointing in same direction as arrow D on tool

- push lever back

! change sanding belts in time

! never fold sanding belts

• Automatic belt centering (ABC)

- centers belt automatically when switching on tool

- keeps belt centered while sanding

In case belt runs o tool (mostly caused by inferior belt

quality), you should

- switch on the tool

- adjust screw E 2 till the sanding belt is running in line

with the at side of the tool

- use new belt, if belt still runs o tool

• Dust suction 5

- empty dustbox G/dustbag F regularly for optimal dust

pick-up performance

- when using tool with vacuum cleaner, mount vacuum

cleaner adaptor H as illustrated (1215)

- when necessary, also clean the lter as illustrated

! do not use dustbox/dustbag/vacuum cleaner

when sanding metal

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Skil 1215 AA Pásová bruska papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Skil. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Skil 1215 AA Pásová bruska v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Skil Pásové brusky
Další manuály Pásové brusky

Často kladené otázky o Skil 1215 AA Pásová bruska

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Skil 7615 AB Pásová bruska

Manuál

Skil 1210 AA Pásová bruska

Manuál

Skil 7640 AA Pásová bruska

Manuál

Skil 1220 MA Pásová bruska

Manuál

Skil 7660 MA Pásová bruska

Manuál

FERM BGM1003 Pásová bruska

Manuál

Extol 8894300 Pásová bruska

Manuál

Einhell TE-BS 8540 E Pásová bruska

Související kategorie