Manuál König KN-WS600 Meteostanice

Manuál

4

will flash a few times right after battery installation. Make sure the vane is pointing due north at the

moment when the red LED flashes and the calibration is now completed. Replace the battery cover and

tighten the screws.

(4) If the wind vane is not pointing due north when the red LED first flashes, remove the batteries and

repeat steps 2 and 3.

(5) Hold the “CHANNEL/SEARCH” buttons on the monitor to search for a remote transmitter. Wind

direction, wind speed, wind chill and channel-1 temperature/humidity readings will appear within

10 minutes if the RF transmission is successful.

5. Selecting a location for the rain gauge

Select a mounting location for the rain gauge that is:

- A flat, level surface

- Within 50 meters (164 feet) of open area from the monitor. Reduce the distance if there are obstacles

between the rain gauge and the monitor

- In an area not blocked on the top or on the sides, so that rain can freely reach the rain gauge (for example,

not under an overhang or too close to a building or fence)

Caution:

- To prevent false rainfall readings caused by water splashes, do not choose a location that is not level or

that is too close to the ground, near a swimming pool or lawn sprinklers, or anywhere water might

accumulate or run off

- The screen in the cylinder of the rain gauge filters most debris (such as leaves) that might fall into the rain

gauge. To avoid frequent build-up of debris in the cylinder, do not mount the rain gauge too close to trees

or plants

6. Battery installation for the rain gauge

(1) Unscrew the 2 screws at each side of the transmitter. Carefully lift the top casing from the base.

(2) Unscrew the 4 screws from the battery compartment cover (identifiable by the battery diagram

markings). Remove the cover and insert 2 AA alkaline batteries as indicated by the polarity symbols

marked inside the battery compartment.

(3) The rain cup has been sealed to prevent tipping and damage during shipping. Before first use, please

remove the seal to allow the rain cup to fill and empty when rainfall occurs.

(4) Replace the battery compartment cover and the screws.

(5) Carefully replace the casing on top of the base. Replace the screws.

(6) Hold the “CHANNEL/SEARCH” button on the monitor for 3 seconds and the total rainfall “- - - -” will

flash. The monitor is now searching for all remote sensors. The total rainfall reading (in this case “0” mm

or inch) will appear within 2 minutes if the RF transmission is successful and the monitor and rain gauge

are now within the effective transmission range.

(7) If total rainfall “- - - -” stops flashing and stays on the display after 2 minutes of searching, the RF

transmission has failed. Shorten the distance between the monitor and rain gauge. Reset the rain

gauge by removing all batteries from the rain gauge and wait for 10 seconds before reinstalling the

batteries. Then repeat steps 5 (and 6) until the RF communication is completed.

7. Mounting the rain gauge

Before mounting the rain gauge, make sure the rain gauge and monitor are within the effective transmission

range and batteries are installed.

(1) Hold the base of the rain gauge flat against the mounting surface then use a level to make sure the rain

gauge (as it rests on the mounting surface) is horizontally level.

(2) Use a pencil to trace the inside of the mounting holes on the base of the rain gauge to mark the screw

locations.

(3) Drill a hole in the center of each marked location and insert the supplied plastic screw plugs.

(4) Hold the rain gauge against the mounting surface so that the holes on the base are aligned with the

plugs, then thread the supplied washer head screws into each hole and use a screwdriver to tighten

them.

8. Installing additional remote thermo-hygrometer sensor(s)

Additional remote thermo-hygrometer sensors can be purchased separately (not supplied with this package).

(1) Select a location for the remote thermo-hygrometer that is within the effective transmission range of

100 meters (328 feet). Shorten the distance if there are obstacles between the monitor and remote

sensor.

(2) Use a small screwdriver to loosen the screws on the battery door of the remote sensor. Insert 2 pieces

of AAA batteries according to the polarity indicated.

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu König KN-WS600 Meteostanice papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Konig. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému König KN-WS600 Meteostanice v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro König Meteostanice
Další manuály Meteostanice

Často kladené otázky o König KN-WS600 Meteostanice

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

König KN-WS520 Meteostanice

Manuál

König KN-WS210 Meteostanice

Manuál

König KN-WS103 Meteostanice

Manuál

König KN-WS400 Meteostanice

Manuál

König KN-WS510 Meteostanice

Manuál

König KN-WS300 Meteostanice

Manuál

König KN-WS100 Meteostanice

Manuál

König KN-WS106 Meteostanice

Související kategorie