Manuál Greenworks G24SDS Rotační kladivo

Manuál

EN

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET

English (Original Instructions)

4

To prevent gear damage, always allow the chuck

to come to a complete stop before changing the

direction of rotation.

To stop the drill, release the switch trigger and allow

the chuck to come to a complete stop.

NOTE: The drill will not run unless the direction of rotation

selector is pushed fully to the left or right.

Avoid running the drill at low speeds for extended periods

of time. Running at low speeds under constant usage

may cause the drill to become overheated. If this occurs,

cool the drill by running it without a load and at full speed.

Using The Auxiliary Handle Assembly (see

gure E)

■ Loosen the handle assembly by turning the handle

counterclockwise.

■ Slide the auxiliary handle assembly onto the hammer

drill in the desired operating position either right

handed or left handed.

■ Securely tighten by turning the auxiliary handle

clockwise.

NOTE

: Be sure the auxiliary handle is securely tightened

against the depth stop rod clamp. This secures the depth

stop rod at the desired depth of cut. It also secures the

auxiliary handle.

Adjusting The Depth Stop Rod (see gure F - G)

■ Lock the switch trigger by placing the direction of

rotation selector in the center position.

■ Press the rod adjustment button.

■ Adjust the depth stop rod so that the drill bit extends

beyond the end of the rod to the required drilling depth.

■ Relese the rod adjustment button.

NOTE

: When properly installed, the teeth on the depth

stop rod should be aligned with the teeth indicator on the

depth stop rod clamp.

Fitting And Changing SDS Bit (see gure H)

This tool is equipped with an SDS Plus connection

system.

■ Clean the bit and grease it with machine grease before

inserting it into the chuck.

■ Pull back the clamp collar and hold it.

■ Push and rotate the dust-free tool into the bit holder as

far as it will go.

■ Release the clamp collar to lock the bit.

■ Check that bit has locked by pulling on it.

Removing The Bit From The SDS Plus System

(see gure I)

■ Pull back the clamp collar and remove the bit.

Mode Selector(see gure J)

In general, rotary mode should be used for drilling and

other heavy duty applications. Hammer mode should be

used for hammer drilling.

To change the operating mode, push the release button

and turn the mode selector switch to the requested

position until it can be heard to latch.

■ For drilling, place the selector in the (

) position.

■ For hammer drilling, set mode selector to (

).

Switch between modes when tool is at a standstill.

NOTE

: Hammer drilling mode will damage the tool’s

mechanism when used for fastening or drilling by non-

SDS Plus bits. Select the rotary mode only on such

purpose.

When hammer drilling, use only bits with hard metal and

SDS Plus shaft only. The use of commercially available

masonry bits with cylindrical shaft by means of the drill

adaptor is impossible.

CAUTION

When hammer drilling, do not apply too much

pressure. Too much pressure will place unnecessary

load on the motor.

Drilling (see gure K)

■ Check the direction of rotation selector for the correct

setting (forward or reverse).

■ Secure the material to be drilled in a vise or with

clamps to keep it from turning as the drill bit rotates.

■ Hold the drill firmly and place the bit at the point to be

drilled.

■ Depress the switch trigger to start the drill.

■ Move the drill bit into the workpiece, applying only

enough pressure to keep the bit cutting. Do not force

the drill or apply side pressure to elongate a hole. Let

the tool do the work.

WARNING

Be prepared for binding at bit breakthrough. When

these situations occur, drill has a tendency to grab

and kick opposite to the direction of rotation and

could cause loss of control when breaking through

material. If not prepared, this loss of control can result

in possible serious injury.

■ When drilling hard, smooth surfaces, use a center

punch to mark the desired hole location. This will

prevent the drill bit from slipping off-center as the hole

is started.

■ When drilling metals, use a light oil on the drill bit to

keep it from overheating. The oil will prolong the life of

the bit and increase the drilling action.

■ If the bit jams in the workpiece or if the drill stalls,

stop the tool immediately. Remove the bit from the

workpiece and determine the reason for jamming.

NOTE

: This drill has an electric brake. When the switch

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Greenworks G24SDS Rotační kladivo papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Greenworks. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Greenworks G24SDS Rotační kladivo v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Greenworks Rotační kladiva
Další manuály Rotační kladiva

Často kladené otázky o Greenworks G24SDS Rotační kladivo

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Total TH115326S Rotační kladivo

Manuál

Skil 3810 DB Rotační kladivo

Manuál

DeWalt D25033 Rotační kladivo

Manuál

Total TH115326-4 Rotační kladivo

Manuál

Parkside IAN 409724 Rotační kladivo

Manuál

Hitachi DH 38SS Rotační kladivo

Manuál

Asist AE1K110G Rotační kladivo

Manuál

Skil 3810 DA Rotační kladivo

Související kategorie