Manuál FERM TDM1012 Stolní vrtačka

Manuál

58 Ferm

SPARE PARTS LIST FTB-13MV

REF NR DESCRIPTION FERM NR

27 MOTOR 311053

37 MAGNETIC SWITCH 311051

50 COVER FOR SPRING 311059

51 SPRING 311058

56 CHUCK GUARD 311055

58 V-BELT 800157

10 CHUCK 311054

- CHUCK KEY 311057

-CONDENSER 311056

- MACHINE VICE TDA 1008

Bench pillar drill with machine vice

THE NUMBERS IN THE FOLLOWING TEXT COR-

RESPOND WITH THE PICTURES AT PAGE 2

TECHNICAL SPECIFICATIONS

PRODUCT INFORMATION

Fig.A

1. On/off switch

2. Drill depth gauge

3. Protection guard

4. Motor

5. Drill depth lever

6. Table adjustment

Check first whether or not the delivery has been dama-

ged by transport and/or whether all the parts are pre-

sent.

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of the

instructions in this manual.

Denotes risk of electric shock.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Keep these instructions in a safe place!

Before using the machine the guidelines must be taken

into consideration. Every mechanical or electrical altera-

tion to the machine which does not meet the applicable

guidelines carries a considerable accident risk.

DURING USE THE FOLLOWING POINTS

MUST BE CONSIDERED:

• Do not remove any mechanical or electrical protec-

tive provisions.

• Check whether all the protective provisions are in

place and have been attached correctly.

• Wear safety goggles during drilling.

• If you have long hair, be sure to wear hair protection

(hair net or cap). Long hair can easily be caught in

moving parts.

• Wear fitted clothing; tie buttons on sleeves.

• Do not hold any workpieces in your hands when dril-

ling. Always use a machine clamp or another clamping

tool.

• Protect workpieces and clamping tools on the bench

to prevent them from getting caught. Fasten them

yourself with screws or clamp them to a machine

clamp fastened to the table.

• Check whether the drill holder is tightened properly.

• Check whether cable lead-throughs are okay.

• To remove drill chips only use hand brushes, brushes,

rubber wipers, chip hooks or similar aids.

• Do not carry out any cleaning or greasing work while

the machine is in operation.

• Always keep V-belts covered (so that your hands

cannot become caught).

• Only tighten the toothed ring drill holder by means of

the wrench.

• Never leave the wrench of the drill holder in the drill

holder! Before switching on the machine, check

whether the wrench really has been removed!

• Do not use any drills which are damaged on the

shank.

• Drill is not suitable to use as press!

• If the mains cable is damaged, it may only be replaced

by a mains cable of the same type.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

Voltage | 230 V

Frequency | 50 Hz

Power input | 350 W

No load speed | 580-2650/min

Number of speeds | 5

Chuck capacity/Morse Conical | 13mm/ B-16

Weight | 20 kg

Lpa (sound pressure level) | 62.1 dB(A)

Lwa (sound power level) | 75.1 dB(A)

Vibration value | 1.57 m/s

2

Ferm 3

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu FERM TDM1012 Stolní vrtačka papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat FERM. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému FERM TDM1012 Stolní vrtačka v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro FERM Stolní vrtačky
Další manuály Stolní vrtačky

Často kladené otázky o FERM TDM1012 Stolní vrtačka

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

FERM TDM1027 Stolní vrtačka

Manuál

FERM TDM1026 Stolní vrtačka

Manuál

FERM TDM1003 Stolní vrtačka

Manuál

FERM TDM1008 Stolní vrtačka

Manuál

Einhell BT-BD 701 Stolní vrtačka

Manuál

Far Tools P 22F Stolní vrtačka

Manuál

Proxxon TBH Stolní vrtačka

Manuál

Dedra DED7708 Stolní vrtačka

Související kategorie