Manuál FERM TCM1001 Rozbrušovačka na dlaždice

Manuál

Caution! For your own safety, carefully read these

instructions for use before using the machine.

TECHNICAL SPECIFICATIONS

6 mm

400 mm

30 -80 mm

0-45

o

TABLE OF CONTENTS:

1. SPECIAL SAFETY INSTRUCTIONS

2. ASSEMBLY

3. HOW TO CUT AND BREAK TILES

4. MAINTENANCE

Faulty and/or discarded electrical or electronic

apparatus have to be collected at the appropriate

recycling locations.

1. SPECIAL SAFETY

INSTRUCTIONS

1. The tile cutting machine is fitted with a replaceable

circular blade. Therefore, keep children away.

2. After use the machine must be stored in a safe and

dry place, away from children.

3. This machine has been designed for cutting and

breaking glazed tiles, and must not be used for any

other purpose.

4. When using the tile cutting machine make sure to

keep extension leads and such away from the

machine.

5. Always place the tile cutting machine on a level and

firm surface.

6. CAUTION! The edges of cut tiles are sharp.

2. ASSEMBLY

Assemble the tile cutting machine as shown in the

drawing.

ASSEMBLY OF THE TILE CUTTING

MACHINE

Remove all the parts from the box and assemble the tile

cutting machine as follows:

1. Slide the black rubber feet (T) over the corners of

the tile cutter. Slide a washer onto the bolt and push

this into the rubber foot. Now slide a washer and a

nut over the bolt on the back and fasten this

properly. Repeat this for the other three corners.

2. Mount the fastening blocks (N) with the 2 tubes (M)

onto the bottom plate (V) using the 4 bolts (O) and

washers (P).

3. Screw the lever (H) onto the tube fastening (I).

4. Finally, mount the sash angle (U) onto the bottom

plate (V) using the knob (S) and washer.

ASSEMBLY OF THE HOLLOW SQUARE

CHISEL

1. Place the hollow square chisel above the hole in the

bottom plate (V).

2. Make sure that the clamping plate (E) comes under

the 2 tubes and fasten this using the socket head

wrench supplied. The socket head wrench is situated

in the black fastening plate (C).

3. It is important that the drill (G) and the knife (F) are

adjusted in such a way that they just touch the

bottom plate (V). This adjustment can be done using

the two nuts at the top of the hollow square chisel.

Then fasten these nuts against each other.

3. HOW TO CUT AND BREAK TILES

1. Use a soft-tipped (carpenter’s) pencil to mark off the

cutting line.

2. Place the tile against the stop, the glazed side facing

upward. The pencil mark must be directly below the

blade.

3. Firmly hold the tile and cut several times (at least 4)

along the mark. After each cut, press the lever more

firmly.

4. Lift the lever when it has reached the front edge of

the tile and moved it backward.

5. Subsequently the break-off unit is lifted. Repeat along

the full width of the tile until the notch is sufficiently

deep.

The cutting movement results from moving the

lever from the back edge of the tile towards its

front, while lightly pressing the lever.

WALL TILES

(single baked)

Lift the lever and position the break-off unit in the middle

of the tile. Press the lever down and the tile will break.

FLOOR TILES

(double-baked):

Sometimes these much harder tiles cannot be cut in two

by means of the break-off unit (K) on the tile cutting

machine.

In these cases after making the notch the tile must be

broken in two by tapping the underside of the tile with a

light hammer along the full length of the notch. This way

the break line will spread through the tile, and cause the

tile to break in two along the line. By means of the wing

nut (Q) the angle of the stop can be adjusted.

MAKING HOLES BY MEANS OF THE (HAND)

DRILL

1. Mount the drill attachment including the drill over

the centre of the hole in the base. It is important that

2 Ferm

Ferm 31

EXPLODED VIEW

SPARE PARTS LIST TCM-495

REF NR DESCRIPTION FERM NR

- SPARE CUTTING WHEEL TCA1001

A ELEVATING ARM 207809

E CLAMPING PLATE 207813

F CUTTER 207803

G CUTTER BRACKET 207802

I PIPE FIXTURE FOR LEVER 207807

K BREAKING HEAD 207805

Q WING NUT WITH WASHER 207819

R ANGLE INDICATOR 207820

WVU

T

S

N

P

O

L

I

H

C

B

A

D

M

E

F

K

G

Z

J

QR

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu FERM TCM1001 Rozbrušovačka na dlaždice papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat FERM. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému FERM TCM1001 Rozbrušovačka na dlaždice v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro FERM Rozbrušovačky na dlaždice
Další manuály Rozbrušovačky na dlaždice

Často kladené otázky o FERM TCM1001 Rozbrušovačka na dlaždice

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

FERM TCM1010 Rozbrušovačka na dlaždice

Manuál

FERM TCM1002 Rozbrušovačka na dlaždice

Manuál

FERM TCM1011 Rozbrušovačka na dlaždice

Manuál

FERM TCM1003 Rozbrušovačka na dlaždice

Manuál

Bosch PTC 640 Rozbrušovačka na dlaždice

Manuál

Einhell TE-TC 18/115 Li-Solo Rozbrušovačka na dlaždice

Manuál

Scheppach FS4700 Rozbrušovačka na dlaždice

Manuál

Fortum 4770803 Rozbrušovačka na dlaždice

Související kategorie