Manuál FERM AGM1095P Úhlová bruska

Manuál

8

EN

Never attempt to remove the guard.

Mounting and removing the wheel disc

(Fig. B)

• Always use suitable wheel disc for this

machine with diameter Ø 100 / 115 / 125 mm

and a bore from 16 / 22 / 22 mm the thickness

of the wheel disc should be 6 mm for wheel

disc for grinding and 3 mm for wheel disc

for cutting, the mounting wheel disc may not

touch the safety guard.

Mounting

• Place the machine on a table with the

protection guard (3) facing upwards.

• Mount the flange (9) onto the spindle (8).

• Place the wheel disc (10) onto the spindle (8).

• Keep the spindle lock button (1) pressed and

firmly tighten the clamping nut (11) onto the

spindle (8) by using the spanner (12).

Removing

• Place the machine on a table with the

protection guard (3) facing upwards.

• Keep the spindle lock button (1) pressed and

loosen the clamping nut (11) using the spanner

(12).

• Remove the wheel disc (10) from the spindle (8).

• Keep the spindle lock button (1) pressed and

firmly tighten the clamping nut (11) using the

spanner (12).

3. OPERATING

Make sure that the work piece is properly

supported or fixed and keep the supply

cord routing away from the work area.

Switching on and off (Fig. A)

• To switch the machine on, press the On/off

switch (2).

• To switch the machine off, release the On/off

switch (2).

Hold the machine away from the work piece when

turning it on and off because the wheel disc could

damage the work piece.

• Clamp the work piece firmly or use another

method to ensure that it cannot move while

working.

• Check the discs regularly. Worn wheel discs

have a negative effect on the machine’s efficien-

cy. Change to a new wheel disc in good time.

• Always first turn the machine off after use

before removing the plug from the socket.

Deburring (Fig. C)

An angle of inclination of 30º to 40º will give the

best results when deburring. Move the machine

back and forth using light pressure. This will

prevent the work piece from discolouring or

becoming too hot and will avoid making groves.

Never use abrasive cutting discs for

deburring work!

Cutting (Fig. D)

For cutting, a special protection guard must be

used (not included).

Maintain firm contact with the work piece to

prevent vibration and do not tilt or apply pressure

and when cutting. Use moderate pressure when

working, appropriate to the material that is

being worked on. Do not slow down wheel discs

by applying sideways counter pressure. The

direction in which you want to cut is important.

The machine must always work against the

direction of the cut; so never move the machine

in the other direction! There is the risk that the

machine will catch in the cut causing kickback

and that you will lose control.

Hints for optimum use

• Clamp the work piece. Use a clamping device

for small work pieces.

• Hold the machine with both hands.

• Switch on the machine.

• Wait until the machine has reached full speed.

• Place the wheel disc on the work piece.

• Slowly move the machine along the work

piece, firmly pressing the wheel disc against

the work piece.

• Do not apply too much pressure on the

machine. Let the machine do the work.

• Switch off the machine and wait for the

machine to come to a complete standstill

before putting the machine down.

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu FERM AGM1095P Úhlová bruska papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat FERM. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému FERM AGM1095P Úhlová bruska v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro FERM Úhlové brusky
Další manuály Úhlové brusky

Často kladené otázky o FERM AGM1095P Úhlová bruska

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

FERM AGM1094P Úhlová bruska

Manuál

FERM AGM1021 Úhlová bruska

Manuál

FERM AGM1003 Úhlová bruska

Manuál

FERM AGM1061S Úhlová bruska

Manuál

FERM AGM1060S Úhlová bruska

Manuál

FERM AGM1029 Úhlová bruska

Manuál

FERM AGM1035 Úhlová bruska

Manuál

FERM AGM1088 Úhlová bruska

Související kategorie