Manuál Bowers and Wilkins HTM3S Reproduktor

Manuál

4

3.5

805S/HTM2D/HTM3S/HTM4S

These systems should be mounted on a

firm shelf or stand that allows the sound

to be properly directed to the listeners.

For the 805S, we recommend the use of

the FS-N805 stand that supports the

speaker at the correct listening height.

For the HTM2D, HTM3S and HTM4S,

the FS-NHTM stand supports these

centre speakers low down so that the

top of the speaker is no higher than

60cm (2 ft) from the floor, commensurate

with positioning them below a large

screen. The stand allows the speaker to

be tilted back by 0º, 4º or 8º.

Follow the instructions supplied with the

stand in each case.

When mounting the speakers on a

bookshelf, stick the 4 self-adhesive

rubber feet to the base of the speaker.

(figure 27)

f Go to section 4.

3.6 SCMS

The speaker is designed to be fixed to a

wall and is supplied with a bracket that

allows adjustment of both horizontal and

vertical angles. (figure 29) The bracket

should be fixed to the wall using screws

in the range 5mm to 6mm diameter

(No.10 to No.12). The screw length

should be chosen to give a minimum of

25mm (1 in) engaged thread. (figure 28)

Hold the template provided against the

wall in the desired position and use a

spirit level to line it up properly. The

outside dimensions of the template

correspond to the rear of the cabinet.

Note especially that the centre of the wall

plate does not coincide with the centre

line of the speaker.

Mark the fixing holes on the wall and drill

and plug the wall.

Ensure that the screw length and

wall plug security are sufficient to

hold the weight of the speaker. When

fixing to drywall construction, try to

arrange for the screws to go into a

stud. B&W can accept no liability for

any failure of wall or ceiling fixings.

Screw the wall plate D to the wall and

test the firmness.

Part screw two of the supplied machine

screws into the upper two threaded

inserts in the back of the cabinet.

Offer the speaker up to the speaker plate

E, locating the two scr

ew projecting from

the back of the speaker into the slots at

the top of the plate.

Fit the remaining two machine screws

through the plate E into the lower

threaded inserts in the cabinet and

tighten all four.

Set the vertical angle of the speaker by

adjusting screw B.

Fully tighten screw A.

Adjust screws C so that the friction of

the three vertical hinges allows you to

adjust the bracket but hold it in place

once set.

Connect the speakers as described in

section 4 before continuing.

Set the required horizontal angle and

push the speaker back to the wall, but

leave a little clearance to avoid rattles.

f Go to section 4.

3.7 DS8S

The speakers may be fixed to a wall or

ceiling using screws in the range 5mm to

6mm diameter (No.10 to No.12).

On the back of the cabinet are three wall

plates. The screw head should be

inserted into the round part of the

aperture and slid fully along one of the

slots. The slots are sprung loaded to

prevent the speaker being readily

knocked out of position. The screw

length should be chosen to give a

minimum of 25mm (1 in) engaged thread.

(figure 28)

Ensure, especially when fixing to drywall

panels, that the screw length and wall

plug security are sufficient to hold the

weight of the speaker. B&W can accept

no liability for any failure of wall or ceiling

fixings.

Use the template provided to mark the

screw positions. The outside dimensions

of the template correspond to the rear of

the cabinet.

Stick 4 of the clear self-adhesive rubber

pads to the rear panel of each speaker,

one close to each corner. These stop the

speaker vibrating against the surface and

help keep it in position. (figure 30)

Adjust the protrusion of the screws such

that the rubber pads are a friction slide

on the surface when the wall plates are

hooked over the screw heads. (figure 31)

Always check and ensure that:

• All the screws slide right to the

ends of the slots in the wall

plates.

• Screw protrusion is adjusted so

that the rubber pads provide

enough friction to prevent the

speakers sliding out of position.

f Go to section 4.

4

CONNECTIONS

All connections should be made with the

equipment switched off.

The terminals accept a variety of cable

terminations to suit most applications –

4mm banana plugs, 6mm and 8mm

(1/4 in and 5/16 in) spades, or bare wires

up to 6mm (1/4 in) diameter.

Important safety notice

In certain countries, notably those in

Europe, the use of 4mm banana

plugs is considered a potential safety

hazard, because they may be

inserted into the holes of

unshuttered mains supply sockets. In

order to comply with European

CENELEC safety regulations, the

4mm holes in the ends of the

terminals ar

e blocked by plastic pins.

If you are using the products in any

country where these conditions

apply, you should ensure that any

banana plugs cannot be used in an

unsafe manner by children or other

uninformed persons.

Ensure each positive terminal on the

speaker (coloured red and marked +) is

connected to the positive output terminal

of the amplifier and negative (coloured

black and marked -) to negative.

Incorrect connection may result in

impairment of frequency response, poor

imaging and loss of bass.

Always screw the terminal caps down

fully to prevent rattles.

Model f Go to

DS8S 4.3

All other models Continue

All models in the range except for the

DS8S may be bi-wired or bi-amplified. In

3-way systems, one set of terminals

feeds the bass drivers and the other the

midrange and tweeter. In 2-way systems,

one set of terminals feeds the bass/

midrange driver and the other the tweeter.

Separation of the signal paths to each

section of the speaker can improve

imaging and the resolution of low-level

detail, and allows the user to optimise

the cable to the frequency range of use.

Bi-wiring involves the use of two

separate 2-core cables from the same

amplifier, one to each pair of terminals.

This is the minimum we would

recommend, but should you prefer to

single wire, perhaps during the initial set-

up pr

ocedur

e or because you do not

want to see a multitude of cables in the

room, you must connect both positive

and both negative speaker terminals

together

.

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Bowers and Wilkins HTM3S Reproduktor papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Bowers and Wilkins. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Bowers and Wilkins HTM3S Reproduktor v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Bowers and Wilkins Reproduktory
Další manuály Reproduktory

Často kladené otázky o Bowers and Wilkins HTM3S Reproduktor

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Bowers and Wilkins CM7 Reproduktor

Manuál

Bowers and Wilkins CMC Reproduktor

Manuál

Bowers and Wilkins CM4 Reproduktor

Manuál

Bowers and Wilkins Formation Duo Reproduktor

Manuál

Bowers and Wilkins DM603 S2 Reproduktor

Manuál

Bowers and Wilkins 704 Reproduktor

Manuál

Bowers and Wilkins CM6 Reproduktor

Manuál

Bowers and Wilkins 804S Reproduktor

Související kategorie