Manuál Ardo FL75GTX Varná deska

Manuál

15

INSTRUCTIONS FOR THE USER

It is necessary that all the operations regarding the installation, adjustment and

adaptation to the type of gas available are carried out by qualified personnel, in

conformity with the regulations in force.

The specific instructions are described in the booklet section intended for the

installer.

USING THE BURNERS

The symbols silk-screen printed on the side of the knob

indicate the correspondence between the knob and the

burner.

Start-up without valves

Turn the corresponding knob anticlockwise up to the

maximum position (large flame, fig. 1) and press.

Automatic start-up with valves

Turn the corresponding knob anticlockwise up to the

maximum position (large flame, fig. 1) and press the knob.

Once the burner has been started up, keep the knob

pressed for about 6 seconds.

Using the burners

In order to obtain the maximum yield without waste of

gas, it is important that the diameter of the pot is suitable

for the burner potential (see the following table), so as to

avoid that the flame goes out of the pot bottom (fig. 2).

Use the maximum capacity to quickly make the liquids

reach the boiling temperature, and the reduced capacity to

heat food or maintain boiling. All of the operating positions

must be chosen between the maximum and the minimum

ones, never between the minimum position and the

closing point.

Use the maximum capacity to quickly make the liquids

reach the boiling temperature, and the reduced capacity to

heat food or maintain boiling. All of the operating positions

must be chosen between the maximum and the minimum

ones, never between the minimum position and the

closing point.

The gas supply can be interrupted by turning the knob

clockwise up to the closing position.

If there is no power supply, it is possible to light the

burners with matches, setting the knob to the start-up

point (large flame, fig. 1).

BURNERS POWER W Ø of pots

Auxiliary 1000 10 - 14 cm

Semi-rapid 1750 16 - 18 cm

Rapid 3000 20 - 22 cm

Triple crown 3800 24 - 26 cm

Double crown 3500 24 - 26 cm

Notice

- When the equipment is not working, always check that

the knobs are in the closing position (see fig.1).

- If the flame should blow out accidentally, the safety

valve will automatically stop the gas supply, after a few

seconds. To restore operation, set the knob to the lighting

point (large flame, fig. 1) and press.

- While cooking with fat or oil, pay the utmost attention as

these substances can catch fire when overheated.

- Do not use sprays near the appliance in operation.

- Do not place unstable or deformed pots on the burner, so

as to prevent them from overturning or overflowing.

- Make sure that pot handles are placed properly.

- When the burner is started up, check that the flameis

regular and, before taking pots away, always lowerthe

flame or put it out.

CLEANING

Before any operation, disconnect the appliance from

the electric grid.

Don’t use a steam cleaner for the cleaning the hob.

It is advisable to clean the appliance when it is cold.

Enamelled parts

The enamelled parts must be washed with a sponge and

soapy water or with a light detergent.

Do not use abrasive or corrosive products.

Do not leave substances, such as lemon or tomato juice,

salt water, vinegar, coffee and milk on the enamelled

surfaces for a long time.

Stainless steel parts

Stainless steel can be stained if it remains in contact with

highly calcareous water or aggressive detergents for an

extended period of time.

The stainless steel parts should also be cleaned with

soapy water and then dried with a soft cloth.

Burners and racks

These parts can be removed to make cleaning easier.

The burners must be washed with a sponge and soapy

water or with a light detergent, wiped well and placed in

their housing perfectly. Make sure that the ame-dividing

ducts are not clogged.

Check that the feeler of the safety valve and the start-up

electrode are always perfectly cleaned, so as to ensure an

optimum operation.

Gas taps

The possible lubrication of the taps must be carried out by

specialized personnel, exclusively.

In case of hardening or malfunctions in the gas taps,

apply to the Customer Service.

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu Ardo FL75GTX Varná deska papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat Ardo. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému Ardo FL75GTX Varná deska v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro Ardo Varné desky
Další manuály Varné desky

Často kladené otázky o Ardo FL75GTX Varná deska

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

Ardo F64GTX Varná deska

Manuál

Ardo FL64GX Varná deska

Manuál

Ardo F6V4X Varná deska

Manuál

Ardo FL6V4GTX Varná deska

Manuál

Ardo SL6V4GTX Varná deska

Manuál

Ardo HT60TV Varná deska

Manuál

Ardo FL64GTX Varná deska

Manuál

Ardo SL75GTX Varná deska

Související kategorie