Manuál AEG WS 7-115 M Úhlová bruska

Manuál

12

WS 7-100 M WS 7-115 M WS 7-125 M

...........

710 W ................710 W ............... 710 W

..........390 W ................390 W ............... 390 W

......10000 min

-1

........10000 min

-1

....... 10000 min

-1

..........100 mm .............115 mm ............. 125 mm

.............M 10 ..................M 14 .................. M 14

...........1,8 kg ................1,8 kg ................ 1,8 kg

..............5 m/s

2

................5 m/s

2

................ 5 m/s

2

............85 dB (A) ...........85 dB (A) .......... 85 dB (A)

............98 dB (A) ...........98 dB (A) .......... 98 dB (A)

ENGLISH

SAFETY INSTRUCTIONS

Please pay attention to the safety instructions in the attached

leaflet!

Appliances used at many different locations including open air

must be connected via a current surge preventing switch.

Always wear goggles when using the machine. It is

recommended to wear gloves, sturdy non slipping shoes and

apron.

Sawdust and splinters must not be removed while the machine is

running.

Always disconnect the plug from the socket before carrying out

any work on the machine.

Only plug-in when machine is switched off.

Keep mains lead clear from working range of the machine.

Always lead the cable away behind you.

After switching off, the machine will not be idle immediately.

(After-running of the work spindle.) Allow the machine to come to

a stop before putting down.

Never reach into the danger area of the plane when it is running.

Always use the auxiliary handle.

Always use the protecting cap when roughing-down and

separating.

Only use tools whose permitted speed is at least as high as the

highest no-load speed of the machine.

Pay attention to the dimensions of the grinding disc. The

mounting hole diameter must fit the mounting flange without

play. Do not use reducer pieces or adapters.

Check grinding tools before use. The grinding tool must be

properly mounted and turn freely. Perform a test run for at least

30 seconds without load. Do not use damaged, out of round or

vibrating grinding tools.

Immediately switch off the machine in case of considerable

vibrations or if other malfunctions occur. Check the machine in

order to find out the cause.

Always use and store the grinding disks according to the

manufacturer's instructions.

When grinding metal, flying sparks are produced. Take care that

no persons are endangered. Because of the danger of fire, no

combustible materials should be located in the vicinity (spark

flight zone). Do not use dust extraction.

Due care should be taken that no sparks or sanding dust flying

from the workpiece come into contact with you.

Never use a cutting disc for grinding. Do not subject cutting discs

to side pressure.

When separating stone the guide shoe must be used!

The adjusting nut must be tightened before starting to work with

the machine.

The workpiece must be fixed if it is not heavy enough to be

steady. Never lead the workpiece to the grinding disk with your

hand.

In case of extreme operating conditions (e.g. when smoothing

metals with the supporting disk and vulcanised fibre disks) strong

contamination can build up inside the angle grinder. In this case,

it is necessary to clean the inside thoroughly and free it from any

metal deposit, due to safety reasons. A residual current

operated device must be superposed. After the current operated

device has come into action, the machine must be subjected to

maintenance.

SPECIFIED CONDITIONS OF USE

This angle grinder can be used for separating and grinding many

different materials, e.g. metal or stone. In case of doubt please

read the manufacturers' instruction.

Do not use this product in any other way as stated for normal

use.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

conformity with the following standards or standardized

documents. HD 400, EN 50144, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3, in accordance with the regulations

98/37/EC, 89/336/EEC

Volker Siegle

Manager Product Development

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the system

voltage indicated on the rating plate. It is also possible to

connect to sockets without an earthing contact as the design

conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all

times.

Use only AEG accessories and spare parts. Should components

need to be exchanged which have not been described, please

contact one of our AEG service agents (see our list of guarantee/

service addresses).

If needed, an exploded view of the tool can be ordered. Please

state the ten-digit No. as well as the machine type printed on the

label and order the drawing at your local service agents or

directly at: AEG Elektrowerkzeuge, Max-Eyth-Straße 10,

D-71364 Winnenden, Germany.

SYMBOLS

Please read the instructions carefully before

starting the machine.

Always wear goggles when using the machine.

Always disconnect the plug from the socket

before carrying out any work on the machine.

Accessory - Not included in standard

equipment, available as an accessory.

TECHNICAL DATA

Nominal power output ...................................................................

Rated output ..................................................................................

Max. no-load speed .......................................................................

Grinding disk diameter ..................................................................

Thread of work spindle ..................................................................

Weight without cable .....................................................................

Typical weighted acceleration in the hand-arm area .....................

Typical A-weighted sound levels:

Sound pressure level ..................................................................

Sound power level ......................................................................

Wear ear protectors!

Measured values determined according to EN 50 144.

Hodnocení

Více o tomto návodu

Chápeme, že je hezké mít k vašemu AEG WS 7-115 M Úhlová bruska papírovou příručku. Manuál si můžete vždy stáhnout z našich webových stránek a vytisknout si jej sami. Pokud byste chtěli mít originální příručku, doporučujeme vám kontaktovat AEG. Možná by byli schopni poskytnout originální návod. Hledáte příručku ke svému AEG WS 7-115 M Úhlová bruska v jiném jazyce? Vyberte si preferovaný jazyk na naší domovské stránce a vyhledejte číslo modelu, abyste zjistili, zda jej máme k dispozici.

Specifikace

Všechny návody pro AEG Úhlové brusky
Další manuály Úhlové brusky

Často kladené otázky o AEG WS 7-115 M Úhlová bruska

Náš tým podpory vyhledává užitečné produktové informace a odpovídá na často kladené otázky. Pokud v nich najdete nějakou nepřesnost, kontaktujte nás prostřednictvím našeho kontaktního formuláře.

Související produkty

Manuál

AEG WS 24-230 Úhlová bruska

Manuál

AEG WS 13-125 XE Úhlová bruska

Manuál

AEG WS 24-230 GVX Úhlová bruska

Manuál

AEG WS 7-100 M Úhlová bruska

Manuál

AEG WS 9-125 Úhlová bruska

Manuál

AEG WS 1000-125 Úhlová bruska

Manuál

AEG WS 24-180 E Úhlová bruska

Manuál

AEG PE 150 Úhlová bruska

Související kategorie